Is There A Way To Repair A Broken Arm On A Pair Of Sunglasses

Download Article

Download Article

Breaking your eyeglasses can be frustrating, and you might not ever exist able to supercede them right away. Whether you scratched the lense, lost a screw, or broke the bridge, you can repair your eyeglasses yourself to agree you lot over until you lot are able to get a new pair.

1. 1

   Use the glue-and-paper method. For an effective temporary fix, it is possible to glue your eyeglass back together to repair a break at the bridge (the part that goes over your nose).

   • Make clean. Make sure that the 2 pieces y'all're trying to glue are clean. (Remove all gum from previous attempts. If information technology's "super glue", fingernail polish with acetone will piece of work merely it's tough on the frames)^[i]
   • Become your supplies in place. Gather upwardly the post-obit: Super Glue (Locktite, Krazy Glue, etc), pieces of glossy wrapping newspaper or thick mag pages that match your frames, sharp scissors
   • Cutting the wrapping paper into thin strips approximating the width of your frames.
   • Glue the paper to your frames, i strip at a time. Employ a short piece of paper as a splint across a broken nosepiece or wrap a longer piece around like an ace bandage.^[2]
   • Await for each piece to dry out before you add together the next

   Advertisement

1. 1

   Get your materials in place. You'll demand a thread, needle, drill, sandpaper, superglue, painter's stir stick, rubber bands, waxed newspaper, cotton swabs, booze or nail polish remover and a hobby pocketknife.

2. two

   Clean and sand the broken pieces. Use sandpaper to clean and rough upwards the broken area to exist glued. Swab the area with some rubbing alcohol or smash polish remover to set up the surface.

3. 3

   Secure the ii pieces together. Cut a piece of a painter's wooden stir stick to fit between the temples (aka, the side pieces) of your glasses. Cover your lenses with wax newspaper to prevent scratching and so wrap a condom band over one end of the stick and secure it to your glasses. Do the aforementioned on the other end.

   • Line the 2 halves up carefully and exist sure the safe bands are belongings things firmly in identify. If it wasn't a clean suspension and there are some gaps, line the pieces up as best you can taking pains to ensure there are some definite points of contact.^[iii]

4. 4

   Glue. Make full the joint at the break with gum; utilize plenty to secure the bridge merely not so much that the mucilage runs out. Squeeze out the mucilage slowly and neatly to avoid bubbles. As yous make full in the joint, be sure that there are no gaps or voids. Use the side of a cotton swab to gently clean upwardly any excess gum; swab it upwards before it has a chance to dry and go tacky. Set the spectacles aside for at least an 60 minutes so the gum tin dry completely.

5. 5

   Drill 2 holes. Choose a small drill bit appropriate for the thickness of your eyeglass frames. Take your hobby knife and dig out pilot holes on either side of the newly repaired joint. Place your glasses down on a soft fabric that's been laid on a table elevation and carefully drill a hole on each side of the break. The holes must be parallel so they can exist used to wrap a ring of thread around the core joint.^[4]

6. vi

   Run up a tension band in identify. Use a fine needle and four to six feet of thread that matches the color of your eyeglass frames to "sew" the 2 sides of the repair together for added strength. Pass the needle and thread through the ii holes every bit many times as you can taking care not to pull too hard and put stress on the newly repaired joint. Cease when at that place'south no more than room. Fill up the drilled holes with gum, soaking the thread and blotting up whatsoever excess with a cotton fiber swab. Trim the edges of the thread and allow the gum to dry for at to the lowest degree an hr.

7. seven

   Add together a wrap. If you desire to requite extra forcefulness to your repair, you can add this additional step to your process. Do not trim the edges of the thread as in a higher place. Instead, after your mucilage has dried, have the remaining thread from 1 side and wrap information technology around the bridge of your glasses from front to dorsum. Make your wrap as smashing as possible; some criss-crossing may exist unavoidable, simply practise your best to preclude the wrap from looking bulky. Go out a brusk stop to exist trimmed later. Soak the wrap with gum and let information technology dry for 10-15 minutes. Take the thread from the other side of your glasses and wrap it effectually the bridge in the reverse management (back to front end). Soak the new wrap in glue and permit it cure for a couple of minutes earlier snipping off the two loose ends. Prepare your glasses aside for 24 hours before wearing.

   Advertisement

1. 1

   Boil water. Fill a small-scale pot with water and set the flame to "loftier." Because yous're going to utilize heat for this repair, the frames of your glasses must be plastic for it to work.

2. 2

   Melt the plastic. Once the h2o is boiling, hold the broken edges of the glasses over the pot and close plenty for the oestrus to soften the edges.

3. iii

   Insert a pin. Push a brusk pivot into 1 edge and and so push the other edge onto the pin. While the plastic is yet hot, shine it over the pivot. ^[5]

   • Never put plastic eyeglass frames directly over a flame.

   Advertizement

1. 1

   Use an eyeglass repair kit. Eyeglass repair kits are readily bachelor at drugstores and contain everything you need to brand a repair--screws, a tiny screwdriver and sometimes a magnifying glass. A newer version of the kit contains longer screws meant to be easier to handle. Y'all insert the screws into the hinges, screw them in and so "snap off" the lesser of the spiral to fit the size of the hinge.

   • If yous're finding it difficult to line upwardly the hinges on your temple piece and front piece, it could considering a hinge mechanism inside the temple piece swivel is holding it back. To correct this, use the claw end of a paper clip, insert information technology through the temple hinge hole and gently pull information technology out. To keep the swivel pigsty in place, insert a second paperclip upright and into the "gap" created when y'all pulled out the hinge hole. Line upwardly the front piece and temple piece holes and insert and tighten the screw. When you're finished, remove the paperclip from the gap and the hinge hole volition slide back into place creating a firm fit for your glasses. ^[6]

2. 2

   Try a toothpick. When a screw falls out of the hinge that holds the front and temple pieces of your glasses together, utilise a toothpick to temporarily take the identify of the screw. Line up the temple hinge holes with the front end holes and button a wooden toothpick through them as far as it volition get. Pause or prune off the excess.^[7]

3. 3

   Substitute with a wire. Strip the paper off of a twist tie (the kind that come on a bag of bread). Line upwards the hinge holes and thread the twist-tie wire through them. Twist the wire in place until the temple feels secure. Cut off the edges of the wire so yous don't become scratched. You can too use a small safety pivot (the ones that are sometimes used with habiliment cost tags). Insert the pin through the holes to concord the side in place.

   Advertisement

1. 1

   Employ baking soda and water. Starting time, wipe off both your lenses with a microfiber cloth. Side by side, mix 1 teaspoon (4.9 mL) of water with 1 tablespoon (xv mL) of baking soda until it forms a paste-like consistency. So, apply the paste to your lenses and gently scrub your lenses with the substance. Afterwards, rinse your glasses with water to wash off the baking soda mixture. This will probable be all yous need to remove the scratches!^[eight]

2. 2

   Employ a household cleaner. Abrasive cleansers can exist used to polish scratched surfaces. Waxy products like Lemon Pledge and Carnauba cleaner wax actually make full light scratches with wax. However, the wax will reduce your visibility and require reapplication every few days. You can too effort rubbing alcohol or diluted ammonia. Subsequently treating your spectacles with 1 of these products, smoothen them with a soft cloth, ideally 1 made especially for cleaning glasses.

3. iii

   Foreclose future scratches. Lenses are delicate and should be treated with care to prevent them from getting scratched.

   • Use an eyeglass case. A sturdy, cushioned instance will protect your eyeglasses; identify them in a example rather than in your pocket or throwing them directly into your pocketbook.^[9]
   • Launder your lenses. Make clean your glasses every day with soapy water and dry them with a clean, soft cloth fabricated for this purpose.
   • Stay away from unfriendly products. Some products can harm your lenses and should be avoided. Don't use facial tissues or paper towels to make clean your lenses and stay away from anti-bacterial soaps when you lot wash them.^[10] Exist careful when using hairspray, perfume or blast polish remover--they can remove the coatings on lenses.

   Advertizing

Ask a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertizement

Video

• Keep glue away from your lenses and your fingers

• In a pinch, the become-to method for fixing a broken bridge is but to wrap tape around information technology to hold the ii pieces in place. Choose a color tape that matches the color of your frames most closely or brand a fashion statement and wrap them in a piece of decorative duct tape.

• If a white residuum develops on the frames from contact with acetone, try rubbing them with an oil based lotion.

Advertising

• Keep glue away from eyes until completely dry

Advertisement

About This Article

Article Summary X

If you lose a screw from your glasses, endeavor purchasing an eyeglass repair kit from a drugstore. These have replacement screws and a tiny screwdriver to make the repair easy. If you tin't find a repair kit, push button a wooden toothpick through the hinge holes. You tin can also wrap a thin piece of wire through the holes and twist it until the temple of your glasses feels secure. If your glasses have a broken bridge, keep reading to larn how to ready it yourself.

Did this summary help you?

Cheers to all authors for creating a page that has been read 750,685 times.

Did this article help you?

Source: https://www.wikihow.com/Repair-Eyeglasses

Posted by: reynayage1950.blogspot.com

Share this post